Compounding Sponge 150mm X M14 White Hard Foam Pad

PACK SIZE

The price displayed for this product is the unit price of the product. Where a PACK SIZE is indicated, this refers to the recommended ordering quantity and is also indicative of how many of these products are packaged in a box.

Brand: TORK CRAFT
Model: TCCS15014-4
Weight: 0.06kg
Dim: 162.00mm x 210.00mm x 210.00mm
UPC: 6009515828387

Price:

R 196.65

Ex VAT: R 171.00

Available Options

Stockist

Compounding sponge

Pattern: Standard
Density: Firm
Colour: White
Diameter: Ø150mm
Thread/Hook & Loop: M14

Application:

The compounding sponge should be used with an automotive polisher.

It is necessary to polish a vehicle body panel when:

The panel has been newly painted with a clear-coat.
Shallow scratch marks need to be removed.
The panel has suffered from oxidation.
Swirl marks and hologram defects need to be removed.

Compounding sponge uses:

COLOUR	POLISH	COMPOUND
White	Good	Best
Orange	Good	Best
Red	Best
Black	Best

Compounding sponge range:

ORDER NO.	DENSITY	COLOUR	DIAMETER	THREAD	PATTERN
SPC00101	Firm	Orange	Ø200mm	Hook & Loop	Standard
SPC00100	Soft	Yellow	Ø200mm	Hook & Loop	Standard
SPC00102	Soft	Red	Ø200mm	Hook & Loop	Standard
TCCS15058	Firm	White	Ø150mm	5/8 UNC	Standard
TCCS15014-1	Firm	White	Ø150mm	M14	Standard
TCCS15014-4	Firm	White	Ø150mm	M14	Standard
TCCS15014	Firm	Orange	Ø150mm	M14	Standard
TCC15014-2	Soft	Red	Ø150mm	M14	Standard
TCCS15014-3	Soft	Black	Ø150mm	M14	Standard
TCCS15014-5	Soft	Black	Ø150mm	M14	Waffle
SPC00124	Firm	Blue	Ø125mm	Hook & Loop	Standard

NOTE:
For the Ø200mm Hook & Loop compounding sponges, use the M14 backing pad SPC00106.

Adaptors to convert or lenghten the polisher's thread:

ORDER NO./td>	MALE THREAD	FEMALE THREAD
SPC00055	5/8 UNC	5/8 UNC
SPC00053	5/8 UNC	M14
SPC00054	M14	5/8 UNC
SPC00052	M14	M14

Compounding sponge

Steps to take when polishing a panel:

1. Preparing the panel:

Sometimes a panel has fine over-spray left from spraying the clear-coat. This needs to be removed by lightly sanding with a fine abrasive paper. All over-spray need to be sanded out up to P1500 grit.
The panel should be washed when all spray-finishing defects have been removed. Any dirt particles could cause scratch marks when polishing.
Tight curves and ends of the panel should be masked-off to prevent the effects caused by point pressure. The polisher should always be used on flat surfaces.

2. Applying the polishing compound:

A five rand coin amount of polishing compound should be applied to the sponge. Switch the polisher to it's lowest speed setting.
Switch on the polisher and gradually spread the polishing compound over the panel.
Keep moving the polisher on the panel to have as little amount of pressure and friction.
The polishing compound will remove the scratch marks caused by the P1500 sand paper and it will bring out an impressive gloss finish.
Remove the masking from the panels and apply the polishing compound to a microfiber cloth. Hand polish (by moving your hand in a small circular motion) the tight curves and ends in the panels until the same finish is achieved as from the polisher.

3. Wash the panel when finished:

Wash the panel after polishing to remove any residue from the polishing compound.

consider safety for your health and the people around you
General safety suggestions: It is advisable to always have the following items nearby and in a good condition Eye protection – clean and scratch free Hearing protection – quality earmuffs Dust masks – discard old and dirty masks Gloves – for easy handling of material and hand protection

Wear Gloves	Eye Protection	Hearing Protection	Dust Mask