Menu
Your Cart

Festool CS 70 SP/10 Splinter Guards for CS 70 PRECISIO 10 Pack

Festool CS 70 SP/10 Splinter Guards for CS 70 PRECISIO 10 Pack
Festool CS 70 SP/10 Splinter Guards for CS 70 PRECISIO 10 Pack
  • Brand: FESTOOL
  • Model: FES490340
  • Weight: 0.21kg
  • Dim: 230 mm x 165 mm x 50 mm
  • UPC: 4014549122358
Price:
R 992.45
Ex VAT: R 863.00

Available Options

Festool CS 70 SP/10 Splinter Guards for CS 70 PRECISIO

At a Glance: Pack of 10 replacement splinter guards for the Festool CS 70, designed to help achieve clean cut edges on both sides of the workpiece.

Give visible furniture and panel components the clean edges they deserve with the Festool CS 70 SP/10 splinter guards. Fitted into the CS 70's dedicated holder and cut to the installed saw blade, each insert helps minimise splintering along the underside of the cut. This is particularly useful when both faces of a component will remain visible. Straightforward replacement makes it practical to renew a worn insert, while the 10-piece pack keeps replacements available for ongoing precision work and furniture manufacture.

Close Support at the Cutting Edge

The blade creates a closely matched slot in a fresh splinter guard during the initial setup. The surrounding insert supports the material beside the cut, helping reduce breakout where the teeth leave the underside of the workpiece.

Product Highlights

  • Cleaner visible edges: Helps make clean cuts on both faces possible when combined with the appropriate blade and setup.
  • Blade-matched opening: The initial cut-in prepares the insert for the fitted saw blade.
  • Less finishing work: Reduced splintering can save time cleaning up cut edges.
  • Easy replacement: Renew the consumable insert in the saw's existing holder.
  • 10-piece supply: Keep fresh guards available for replacement and separately prepared setups.

Product Compatibility

  • Festool CS 70 PRECISIO: Manufacturer-listed accessory for the CS 70 saw family.
  • CS 70 EG and CS 70 EBG: Used in the designated splinter guard holder, following the instructions for the specific machine version.
  • Blade and angle preparation: The insert must be prepared for the fitted blade and the cutting angle permitted by the saw's operating instructions.

Check the Instructions Before Bevel Cutting

CS 70 operating instructions differ by version. Earlier instructions require the splinter guard to be removed for bevel cuts; later instructions permit a separate guard to be fitted and cut in for each angle. Follow the instructions applicable to your exact saw.

Features

  • Dedicated CS 70 insert: Fits the saw's purpose-designed splinter guard arrangement.
  • Cut-in design: Creates clearance matched to the blade during commissioning.
  • Replaceable working edge: Allows a worn or damaged insert to be renewed.
  • Pack quantity: Supplied as 10 individual splinter guards.

Benefits

  • Better presentation: Helps preserve the appearance of components with two visible faces.
  • Consistent preparation: A fresh insert provides close support beside the blade slot.
  • Convenient maintenance: Keep replacements on hand for workshop and installation work.

Application

  • Precision cutting during furniture manufacture.
  • Preparing cabinet panels and components with visible faces.
  • Reducing underside breakout on suitable veneered or coated panels when using the correct blade.
  • Replacing inserts whose blade openings have become worn or damaged.

Extra Information

  • Initial preparation: A new insert must be cut in using the fitted blade before normal work.
  • Height setting: The CS 70 instructions describe the raised section protruding approximately 0.3 mm above the table; check and adjust the holder according to your manual.
  • Cut quality: Blade selection, blade condition, feed technique and workpiece support also influence the finished edge.

Keep the Slot Closely Matched

An enlarged or damaged blade opening provides less support immediately beside the cut. Inspect the insert when changing blades or when edge quality deteriorates, and fit a fresh guard where necessary.

Pro Tips

  • Label prepared inserts with their blade and angle setup so you can identify them later.
  • Use a sharp blade suited to the material; the splinter guard supports the cut but blade choice remains important.
  • Make a trial cut in matching scrap material before cutting finished components.
  • Keep the holder and table insert seating areas clear of chips before fitting a replacement.

How to Use

  • Switch off the saw, wait for the blade to stop and disconnect the mains plug.
  • Follow the saw manual to remove the table insert, lower the blade and access the splinter guard holder.
  • Remove the old guard and slide the fresh insert fully into its designated holder.
  • Check the holder height, refit and secure the table insert, and restore the required protective components.
  • Follow the machine's prescribed cut-in procedure. The CS 70 instructions describe running the saw and slowly raising the blade from minimum to maximum cutting height to form the slot.
  • Switch off, wait for a complete stop and unplug before inspecting or adjusting the installation.
  • With the saw correctly reassembled, make a test cut and confirm edge quality before starting production work.

Safety

  • Disconnect the mains plug before fitting, removing or manually adjusting the insert.
  • Perform the powered cut-in procedure only as described in the operating instructions, with the machine correctly assembled and hands clear of the blade.
  • Keep the required blade guard and riving knife correctly fitted for the cutting operation.
  • Use suitable eye, hearing and respiratory protection, appropriate dust extraction and the prescribed workpiece guidance.
  • Check the saw-specific restrictions before bevel cutting and replace damaged or insecure inserts.

Specifications

DescriptionSpec
BrandFestool
Cat No.FES490340
Manufacturer Order No.490340
ModelCS 70 SP/10
Product TypeReplacement splinter guard insert
Compatible SawFestool CS 70 PRECISIO
Primary FunctionReduces underside splintering to support clean cut edges on both faces
Mounting PositionDedicated splinter guard holder beneath the table insert
Initial PreparationCut in using the fitted blade according to the saw instructions
Pack Quantity10 pieces

Scope of Delivery:

  • 10 x Festool CS 70 splinter guard inserts.
Scope of delivery note: Saw, saw blade, table insert and splinter guard holder are not included.
Cookie Notice:
We Use Cookies... In addition to the cookies that are strictly necessary for the operation of this website, Vermont Sales uses cookies and other tracking tools to remember your preferences and to measure our website performance. Rest assured, your information is safe with us and we will NEVER share it with any other party. Privacy Policy