Menu
Your Cart

Wire End Brush 24mm x 6mm Shaft Max 4500 RPM

Wire End Brush 24mm x 6mm Shaft Max 4500 RPM
Wire End Brush 24mm x 6mm Shaft Max 4500 RPM
  • Brand: TORK CRAFT
  • Model: TCWE2406
  • Weight: 0.06kg
  • Dim: 62 mm x 130 mm x 130 mm
  • UPC: 6009515805944
Price:
R 57.27
Ex VAT: R 49.80

Available Options

Tork Craft Wire End Brush 24mm x 6mm Shaft For Drill Max 4500 RPM

At a Glance: Wire end brush for use with a drill, featuring a 24mm minimum brush diameter, up to 34mm maximum working diameter, 6mm shaft and a maximum operating speed of 4500 RPM

The Tork Craft TCWE2406 Wire End Brush is a rotary cleaning accessory designed specifically for use with a suitable drill. Its end-brush format concentrates the wire bristles into a relatively small working area, making it particularly useful for removing rust, corrosion, scale and surface contamination from confined areas, recesses, corners and other difficult-to-reach locations. The brush has a 24mm minimum diameter, can expand during operation to approximately 34mm maximum diameter and uses a 6mm shaft for secure mounting in a compatible drill chuck.

Wire end brush for drill use – maximum 4500 RPM

Wire end brushes provide concentrated cleaning action for detailed surface preparation and maintenance work. The TCWE2406 has a minimum brush diameter of 24mm and may expand during operation to a maximum working diameter of approximately 34mm. It is designed for drill use and must always be operated at or below its stated maximum speed of 4500 RPM.

Product highlights

  • For drill use Designed for mounting in a compatible drill chuck.
  • Maximum 4500 RPM Do not operate the brush above its rated maximum speed.
  • 24mm minimum brush diameter Compact end-brush profile for targeted cleaning.
  • Up to 34mm maximum brush diameter Allows for normal outward bristle expansion during operation.
  • 6mm shaft Fits compatible drill chucks securely.
  • End brush design Useful for recesses, corners, holes and concentrated surface cleaning.
  • Blister packed Convenient individual packaging for storage and identification.

Features

  • Wire end brush Designed for rotary surface cleaning and preparation.
  • 24mm minimum brush diameter Provides a concentrated working area for detailed applications.
  • 34mm maximum brush diameter Allows for normal bristle expansion while operating.
  • 6mm shaft Suitable for compatible drill chucks.
  • 4500 RPM maximum speed Rated for controlled drill use within this limit.
  • End brush profile Helps access confined and recessed working areas.
  • Blister packaging Supplied individually for convenient retail display and storage.

Benefits

  • Effective rust removal: Wire bristles help remove loose rust, corrosion, scale and surface deposits.
  • Access difficult areas: The end-brush shape is useful where larger wheel or cup brushes may not fit.
  • Controlled cleaning: The concentrated brush profile allows targeted work on specific areas.
  • Convenient drill mounting: The 6mm shaft fits directly into compatible drill chucks.
  • Versatile workshop use: Suitable for maintenance, restoration, fabrication and general surface preparation tasks.

Application

  • For use with compatible electric or cordless drills
  • Removing loose rust and corrosion
  • Cleaning metal surfaces and components
  • Removing scale, oxidation and surface deposits
  • Cleaning recesses, corners and confined areas
  • Surface preparation before coating, painting or finishing
  • Workshop, automotive, maintenance and fabrication applications

Extra Information

  • IMPORTANT: Maximum operating speed is 4500 RPM.
  • This brush is intended for use with a suitable drill and should not be used in high-speed die grinders.
  • Always check the drill speed setting before starting work.
  • The brush has a minimum diameter of 24mm and may expand up to approximately 34mm during operation.
  • Allow the wire tips to perform the cleaning action rather than forcing the brush against the surface.
  • The 6mm shaft must be fully and securely clamped in the drill chuck before use.
  • Wire brushes are consumable accessories and will gradually wear during normal operation.

Pro Tips

  • Start the drill at a lower speed and increase gradually while remaining below 4500 RPM.
  • Use light, controlled pressure to help extend brush life and improve cleaning performance.
  • Keep the brush moving across larger surfaces to achieve a more even finish.
  • For recesses and confined areas, allow the bristle tips to contact the surface without excessive side pressure.
  • Inspect the brush before every use and replace it if wires are excessively worn, damaged or loose.

How to Use

  • Disconnect or switch off the drill before fitting the brush.
  • Insert the 6mm shaft fully into the drill chuck.
  • Tighten the chuck securely around the shaft.
  • Confirm that the drill speed will not exceed 4500 RPM.
  • Wear suitable eye, face and hand protection before starting work.
  • Start the drill away from the workpiece and allow the brush to reach operating speed.
  • Bring the wire brush gently into contact with the surface.
  • Use light pressure and allow the wire tips to perform the cleaning action.
  • Move the brush steadily across the required area without forcing it.
  • Switch off the drill and allow the brush to stop completely before setting the tool down.

Safety

  • FOR DRILL USE ONLY. NEVER EXCEED 4500 RPM. Check the drill's speed settings before operating.
  • Wear eye protection, a face shield, hearing protection and suitable dust protection for the task. Wire brushes can eject loose wires and debris.
  • Disconnect the power or remove the battery before fitting, adjusting or removing the brush.
  • Ensure the 6mm shaft is securely clamped in the chuck and the accessory runs correctly before contacting the workpiece.
  • Use rotary drilling mode with hammer or percussion action switched off.
  • Secure the workpiece and maintain firm control of the drill throughout use.
  • Keep hands, loose clothing, jewellery and long hair clear of the rotating brush.
  • Keep bystanders away from the work area and out of the path of flying debris.
  • Use light pressure. Stop if the brush catches, vibrates excessively or sheds an unusual amount of wire.
  • Do not use a brush with a bent shaft, damaged holder, loose wires or excessive wear.
  • Keep sparks and debris away from flammable materials.
  • Wait until the brush stops completely before setting the drill down or touching the accessory.

Specifications

Description Spec
Brand Tork Craft
Cat No. TCWE2406
Product Type Wire End Brush
Brush Minimum Diameter 24mm
Brush Maximum Diameter 34mm
Shank Diameter 6mm
Maximum Speed 4500 RPM
Recommended Tool Compatible Drill
Package Type Blister
Application Cleaning, Rust Removal And Surface Preparation
Tool Type Rotary Wire Brush Accessory
Primary Use Targeted Rotary Surface Cleaning
Applications Workshop, Automotive, Maintenance, Restoration And Fabrication Use
Suitable For Compatible Drills With 6mm Shank Capacity

In the box:

  • 1 x Tork Craft Wire End Brush 24mm x 6mm Shaft
Cookie Notice:
We Use Cookies... In addition to the cookies that are strictly necessary for the operation of this website, Vermont Sales uses cookies and other tracking tools to remember your preferences and to measure our website performance. Rest assured, your information is safe with us and we will NEVER share it with any other party. Privacy Policy