Our Products
Resellers
Find your closest reseller:
Within:
Brands
Our News
Selling to Public01/02/2017
We do not sell to the public

STRAIGHT BIT 7/8"(22.2MM) X 3/4"(19MM) TWO FLUTE 1/4" SHANK

STRAIGHT BIT 7/8"(22.2MM) X 3/4"(19MM) TWO FLUTE 1/4" SHANK
Brand: PRO-TECH
Product Code: KP209
Barcode: 6009600400849
Availability: Out Of Stock
Recommended Price: R284.63
Excluding VAT: R247.50

New Stock Expected:
  • 30/04/2020
Pro-Tech. South African favourite for over 30 YearsDouble flute Straight bit

Two-flute Straight bit KP209In choosing a straight bit for any application, always select one with the shortest cutting edges and the shortest overall length that will reach the required cut depth. Excessive length intensifies deflection and vibration, which degrade cut quality and lead to tool breakage.

Use a two-flute bit where fine finish is paramount. Two flutes balance the bit, eliminating vibration that degrades the cut finish.

Two cuts per revolution yield a smooth surface, but feed rate is slightly reduced.

This router bit has a 6.35mm shank (shaft) that will fit most small routers. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.

 

PRO-TECH router bits are manufactured in Taiwan.

Part No. Shank dia. Cutting width Cutting Height Radius (r)
KP209 1/4 in (6.35mm) 22.20 mm ( 7/8 in ) 19.01 mm ( 3/4 in ) Straight

 

Length of Shank: 32 mm

Straight bit, 2 Flute, TCT - 22.2 mm cutting widthCutting sample 

 

Take CareFull Speed

 

consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection – clean and scratch free
  • Hearing protection – quality earmuffs
  • Dust masks – discard old and dirty masks
  • Gloves – for easy handling of material and hand protection
Wear Gloves Eye Protection Hearing Protection Dust Mask
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

To use router bits safely (and to get the best results from your router), the router bits need to be installed properly into the router's collet. Improper installation of your bits can cause excessive chatter and could increase the likelihood that the bits will break when in use. 

Clean and sharp

First of all, before beginning any routing operation, check your bits to make sure that they are clean, relatively free of pitch, and most of all, sharp. If the bit is dull, chipped, is excessively burned or has any other defect, it should be sharpened or replaced before use. 

Correct collet and collet nut fit

Most router collets have a recess (groove) that needs to click into a circlip that resides inside the collet nut. Failing to ensure that the collet "clicked" into the collet nut will cause you to struggle to remove the router bit after tightening. This could cause the collet to break or be removed by a technical repair centre.

 

Correct fit inside the collet

When installing the bit into the collet, do not tighten the collet with the bit "seated." Instead, insert the bit until the shank (bit shaft) reaches the bottom of the collet, then ease it out about 2 mm before tightening the collet.

When the bit is tightened, there should be no less than  2/3 's of the length of the shank in the collet. If your bit has a shank that is too short, then the bit should be replaced. 

 

Safety gear

There are a few other safety measures to keep in mind whenever you use your router. First of all, remember to always wear appropriate safety gear as indicated above.

Correct speed setting

Second, be sure to set your router to the proper speed for your router bit. Setting your router to an incorrect speed will not only affect the router's performance, but also can cause the bit to break much more easily and even cause bodily harm. The speed at which a router bit turns can be important. The typical router runs at about 22,000 rpm, which is fine for most bits. But as the diameter of the bit increases, you’ll want to slow things down.

Also, before beginning any routing operation, be certain that you give the router's motor time to come up to full speed for the chosen setting. Beginning to cut before the bit is at full speed can give less than desired results. 

Speed Settings